Wholesale Sterile Syringe Filters for HPLC

0.45um Syringe filters are normally used in scientific research laboratories to remove certain sized particles or bacteria from certain volume of liquid or gas prior to analysis or cell culture. 0.45um Syringe filters are popularly used in HPLC analysis.

The syringe filter produced by Aijiren is often used to filter impurities in the reagents to be tested. After the impurities are filtered, the reagents can be sucked into the autosampler. If the syringe filter is not used, it may cause problems such as clogging the needle hole with impurities in the reagent.

Aijiren’s 2ml Screw Vial is often used to hold samples into the autosampler for testing. The samples are often chemical reagents. If impurities appear in the chemical reagents, the test results will be affected. Therefore, we will use the Syringe Filter to filter, and inject the filtered reagents into 2ml Screw Vial, and then put it into the Autosampler for testing.

Aijiren Syringe Filters are simply quality filters, well packaged, and offered at a fair and competitive price.
25mm diameter syringe filter:
Filter Ø: 25 mm
Filtration area: 4.08 cm2
Housing material: polypropylene
Holdup volume: <100 µl Sample volume: <100 ml

Aijiren is the leading supplier of chromatography consumables, can offer hplc vials,hplc syringe filter, EPA VOA vials, and some other test tubes.
Any requirement for chromatography consumables, please contact us.

In HPLC analysis, the particle size of the chromatographic column packing is small and it is easy to be blocked by impurity particles. Therefore, samples and solvents need to be filtered in advance to remove particulate contaminants and protect the instrument.

When filtering samples choose right membrane syringe filter is very important. If you choose wrong syringe filters your chromatogrpahy instrument will be failed, which can waste a lot of time and money since liquids are normally very expensive. Aijiren provides cost-effective non-sterile and individual packed sterile syringe filters from Nylon, PES, PP, PTFE, PVDF, RC, etc. welcome to inquiry E-mail:info@aijirenvial.com whatsapp:+8618336073276

Aijiren Syringe Filter is used for fast and reliable filtration of small and medium quantities of samples. It has been connected to the filter unit and is widely used in the laboratory.
Diameter: 13mm and 25mm
Pore size: 0.22um and 0.45um
Maximum Operating Temperature:60 ℃
Sterilization: Autoclave at 121 ℃ for 20 minutes

The syringe filter provided by Aijiren has different sizes, 13mm and 25mm, which are convenient to install on the autosampler needles of autosamplers of different sizes. In addition, customers can also choose syringe filters of different materials according to the type of reagents, such as Nylon, PVDF, PTFE, PES, MCE, PP, Cellulose Acetate, etc.

Available in sterile and non-sterile options

Other Membranes are available.

Membrane: PTFE, PVDF, PES, MCE, NYLON, PP, CA, etc. Aijiren disposable sterile syringe filter devices are designed to provide fast and efficient filtration of aqueous and organic solutionsfrom small volumes up to 100 mL.

High purity virgin polypropylene housing, no dyes or pigments added
Every unit type is available as an individually wrapped gamma sterilized pack
A unique concentric funnel-shaped barrel increases volume and decreases back pressure
Color-coded for easy identification
Place of Origin: China (Mainland)
Sample: Free
Payment: 100% T/T in advance

PTFE membranes are inherently hydrophobic; they are ideal for the filtration of nonpolar liquids and gases.
Strong chemical stability and inertia
Non-pyrogenic, and DNA? free
Autoclavable
Product Dimensions ‎3.45 x 3.45 x 3.45 inches; 4.97 Ounces
Item Weight ‎5 ounces
Certification: ISO9001:2022
Place of Origin: China (Mainland)

The filter construction facilitates exceptional loading capacity with fast flow rates. This prevents the build-up of back pressure typically caused by the blocking of an unprotected membrane.
Membrane material: Nylon
Housing: Polypropylene(PP) housing
Connectors: Inlet: Female Luer
Outlet: male slip Luer
Maximum Operating Temperature:60 ℃
Pack: 100 units/pack

Individually packaged, 100pcs per pack, 40PK/carton.56*50*26cm.

PTFE membranes are inherently hydrophobic; they are ideal for the filtration of nonpolar liquids and gases.
Very resistant to solvents as well as acids or bases.
Can be made more hydrophilic by flushing with alcohol, followed by water
Used for filtering and de-gassing chromatography solvents
Permits optimal utilization of small sample volumes
Excellent chemical compatibility for filtering harsh chemicals that destroy other membrane materials
Moisture barrier for venting applications and vacuum pump line protection
Ideal for aerosol sampling
Filter viscous organic-based HPLC samples
After pre-wetting with alcohol, may be used for fine particle removal of aqueous and mild organic solutions in Ion Chromatography

In HPLC analysis, the particle size of the chromatographic column packing is small and it is easy to be blocked by impurity particles. Therefore, samples and solvents need to be filtered in advance to remove particulate contaminants and protect the instrument. Syringe filters can be used in HPLC analysis and IC analysis to filter sample solutions, which is an important step in the sample pretreatment process. 
Non-sterile Disposable Syringe Filters typically consist of a PP housing, which is often made from materials such as polypropylene. The housing contains a filter membrane, which is usually made of materials like PTFE, PVDF, PES, MCE, NYLON, PP, CA, etc. Non-sterile Disposable Syringe Filters are available in a variety of membrane choices, which determine the size of particles or contaminants that can be effectively removed. Available in 13 mm and 25 mm diameters and 0.22 μm and 0.45 μm pore sizes. The choice of pore size depends on the specific application, with smaller pores being used to filter out smaller particles and larger pores for faster flow rates with less fine filtration.

Usage: Laboratory Analysis
Logo: Customized Accepted
Trademark: Aijiren
Origin: China
OEM: Available
Sample: Provided Freely

In HPLC analysis, the particle size of the column packing is small and is easily blocked by impurity particles. Therefore, samples and solvents need to be filtered in advance to remove particulate contaminants and protect the instrument. Different pore sizes filter pollutants of different sizes. Individually packaged, 100pcs per pack, 40PK/carton.56*50*26cm.12.5KG.packed in PP-Trays with plastic film and cover plate, neutral cartons outside OEM packing can be also provided.

PTFE membranes are inherently hydrophobic; they are ideal for the filtration of nonpolar liquids and gases.
Strong chemical stability and inertia
Non-pyrogenic, and DNA? free
Autoclavable
Product Dimensions ‎3.45 x 3.45 x 3.45 inches; 4.97 Ounces
Item Weight ‎5 ounces
Certification: ISO9001:2022
Place of Origin: China (Mainland)

The syringe filter provided by Aijiren has different sizes, 13mm and 25mm, which are convenient to install on the autosampler needles of autosamplers of different sizes. In addition, customers can also choose syringe filters of different materials according to the type of reagents, such as Nylon, PVDF, PTFE, PES, MCE, PP, Cellulose Acetate, etc.

PTFE membranes are inherently hydrophobic; they are ideal for the filtration of nonpolar liquids and gases.
Very resistant to solvents as well as acids or bases.
Can be made more hydrophilic by flushing with alcohol, followed by water
Used for filtering and de-gassing chromatography solvents
Permits optimal utilization of small sample volumes
Excellent chemical compatibility for filtering harsh chemicals that destroy other membrane materials
Moisture barrier for venting applications and vacuum pump line protection
Ideal for aerosol sampling
Filter viscous organic-based HPLC samples
After pre-wetting with alcohol, may be used for fine particle removal of aqueous and mild organic solutions in Ion Chromatography

Fast delivery, all goods can be shipped in 3-7days. Large qty products are in stock for customer.

30mm diameter syringe filter:
Filtration area: 4.9cm2
Housing material: polypropylene
Holdup volume: <100 µl Sample volume: <120 ml Max. housing pressure: 8 bar Maximum Operating Temperature: 80°C (Housing only, also dependent on membrane) Maximum Operating Pressure: 87 psi (Housing only, also dependent on membrane)

Available in two different diameters to suit the applications
Individually wrapped.
Beyond the extensive product selection found within our standard syringe filter list, we offer OEM capabilities for engineering, molding, and insertion of any additional membrane and membrane/pre-filter options.  
Filter insertion in a cleanroom by manual as well as fully automated means.
Brand Name: Aijiren
Packing: 100pcs/pk
For Use With (Application): GC, HPLC

Other Membranes are available.

Disposable
Luer-Lock and pressure fitting
Ultrasonically bonded for reliability
Filter media type clearly inscribed on barrel
Excellent unit-to-unit and lot-to-lot reproducibility and consistency

13mm diameter syringe filter:
Filter Ø: 13 mm
Filtration Area: 1.09 mm2
Housing material: polypropylene
Holdup volume: <20 µl Sample volume: <10 ml Maximum Operating Temperature: 130°C (Housing only, also dependent on the membrane) Maximum Operating Pressure: 87 psi (Housing only, also dependent on the membrane)

Aijiren Syringe Filters are simply quality filters, well packaged, and offered at a fair and competitive price.
25mm diameter syringe filter:
Filter Ø: 25 mm
Filtration area: 4.08 cm2
Housing material: polypropylene
Holdup volume: <100 µl Sample volume: <100 ml

The syringe filter produced by Aijiren is often used to filter impurities in the reagents to be tested. After the impurities are filtered, the reagents can be sucked into the autosampler. If the syringe filter is not used, it may cause problems such as clogging the needle hole with impurities in the reagent.

In HPLC analysis, the particle size of the chromatographic column packing is small and it is easy to be blocked by impurity particles. Therefore, samples and solvents need to be filtered in advance to remove particulate contaminants and protect the instrument. Ion chromatography, which is commonly used in environmental analysis, also requires that no inorganic pollutants be introduced in sample pretreatment. Syringe filters can be used in HPLC analysis and IC analysis to filter sample solutions, which is an important step in the sample pretreatment process.

In HPLC analysis, the particle size of the chromatographic column packing is small and it is easy to be blocked by impurity particles. Therefore, samples and solvents need to be filtered in advance to remove particulate contaminants and protect the instrument. Syringe filters can be used in HPLC analysis and IC analysis to filter sample solutions, which is an important step in the sample pretreatment process. 
Non-sterile Disposable Syringe Filters typically consist of a PP housing, which is often made from materials such as polypropylene. The housing contains a filter membrane, which is usually made of materials like PTFE, PVDF, PES, MCE, NYLON, PP, CA, etc. Non-sterile Disposable Syringe Filters are available in a variety of membrane choices, which determine the size of particles or contaminants that can be effectively removed. Available in 13 mm and 25 mm diameters and 0.22 μm and 0.45 μm pore sizes. The choice of pore size depends on the specific application, with smaller pores being used to filter out smaller particles and larger pores for faster flow rates with less fine filtration.

Aijiren Syringe Filter is used for fast and reliable filtration of small and medium quantities of samples. It has been connected to the filter unit and is widely used in the laboratory.
Diameter: 13mm and 25mm
Pore size: 0.22um and 0.45um
Maximum Operating Temperature:60 ℃
Sterilization: Autoclave at 121 ℃ for 20 minutes

The filter construction facilitates exceptional loading capacity with fast flow rates. This prevents the build-up of back pressure typically caused by the blocking of an unprotected membrane.
Membrane material: Nylon
Housing: Polypropylene(PP) housing
Connectors: Inlet: Female Luer
Outlet: male slip Luer
Maximum Operating Temperature:60 ℃
Pack: 100 units/pack

✅Uniform Pore Size – PTFE Syringe Filter with uniform pore size, high porosity, and high retention efficiency. 13mm disc diameter, 0.22μm, pore size, 100 pcs barreled packed.
✅ High-Quality – ISO 9001 certificated, ensuring the quality of the filter from the first inspection, mind-control inspection, patrol inspection, and warehouse inspection.
✅Non-Sterile Syringe Filters – PTFE syringe filters housing is made of premium polypropylene(PP) material with a unique threaded interface (Luer lock) design, non-sterile, no adhesive, and no contamination of the sample. It can be autoclaved and sterilized at 121°C/249.8℉ for 30 minutes.
Sample: Free
Payment: 100% T/T in advance
Certificate: ISO9001:2015

Syringe filters can be used in HPLC analysis and IC analysis to filter sample solutions, which is an important step in the sample pretreatment process.

Membrane: PTFE, PVDF, PES, MCE, NYLON, PP, CA, etc. Aijiren disposable sterile syringe filter devices are designed to provide fast and efficient filtration of aqueous and organic solutionsfrom small volumes up to 100 mL.

PTFE membranes are inherently hydrophobic; they are ideal for the filtration of nonpolar liquids and gases.
Very resistant to solvents as well as acids or bases.
Sample: Free
Usage: Laboratory Analysis
OEM: Available

Multi-process mold extensions for inclusion of single or multi-level prefiltration media.
Digital variable print capabilities along an arc on barrel face for identification purposes.
Blister packing for EO and gamma sterilization.
Pure virgin PP, verified by HPLC against U/L extractable.
Payment: 100% T/T in advance
Certificate: ISO9001:2015
Brand Name: Aijiren

✅Hydrophobic PTFE Membrane – The PTFE needle filter material is a PTFE membrane, with the naturally hydrophobic, it with broad chemical compatibility and strong chemical stability and inertia, strong hydrophobicity.
✅Uniform Pore Size – PTFE Syringe Filter with uniform pore size, high porosity, and high retention efficiency. 13mm disc diameter, 0.22μm, pore size, 100 pcs barreled packed.
✅ High-Quality – ISO 9001 certificated, ensuring the quality of the filter from the first inspection, mind-control inspection, patrol inspection, and warehouse inspection.
✅Non-Sterile Syringe Filters – PTFE syringe filters housing is made of premium polypropylene(PP) material with a unique threaded interface (Luer lock) design, non-sterile, no adhesive, and no contamination of the sample. It can be autoclaved and sterilized at 121°C/249.8℉ for 30 minutes.
Usage: Laboratory Analysis
Logo: Customized Accepted

Sterile syringe filters are small, disposable devices used in laboratory and medical settings to filter and sterilize liquid samples before they are injected or analyzed. These filters are designed to remove impurities, particulate matter, bacteria, and other contaminants from liquids, ensuring that the filtered solution is free from any potential sources of contamination. Sterile syringe filters typically consist of a PP housing, which is often made from materials such as polypropylene. The housing contains a filter membrane, which is usually made of materials like PTFE, PVDF, PES, MCE, NYLON, PP, CA, etc. Sterile syringe filters are available in a variety of membrane choices, which determine the size of particles or contaminants that can be effectively removed. Available in 13 mm and 25 mm diameters and 0.22 μm and 0.45 μm pore sizes. The choice of pore size depends on the specific application, with smaller pores being used to filter out smaller particles and larger pores for faster flow rates with less fine filtration.

Individually packaged, 100pcs per pack, 40PK/carton.56*50*26cm.

Aijiren is the largest chromatography consumable manufacturer in south of China. There are HPLC vial, GC vial, Septum and closures, EPA vial, TOC vial, Test tube, Reagent bottle and Syringe filter in Aijiren shop. You can get all the consumables in wholesale price. Please choose your needed in precise catalog.

Zhejiang Aijiren Technology, Inc. is a global supplier of life-science, chemistry, laboratory consumables, etc. Our major products are high performance liquid chromatography & gas chromatography consumables such as Chromatography Autosampler Vials with closures, inserts, crimper and syringe filters, etc; Water analysis consumables such as COD test tube.

13mm diameter syringe filter:
Filter Ø: 13 mm
Filtration area: 1.09 mm2
Housing material: polypropylene
Holdup volume: <20 µl Sample volume: <10 ml Maximum Operating Temperature: 130°C (Housing only, also dependent on membrane) Maximum Operating Pressure: 87 psi (Housing only, also dependent on the membrane) Inlet: Luer locks female Outlet: Luer slipped male

Applications:
• HPLC aqueous sample preparation
• Biological sample preparation
• Buffer solutions
• Salt solutions
• Tissue culture media
• Irrigation solutions
• Sterile isolation
• Medical use, sterile filtering protein solution, tissue culture media, additives.

Aijiren’s 2ml Screw Vial is often used to hold samples into the autosampler for testing. The samples are often chemical reagents. If impurities appear in the chemical reagents, the test results will be affected. Therefore, we will use the Syringe Filter to filter, and inject the filtered reagents into 2ml Screw Vial, and then put it into the Autosampler for testing.

In HPLC analysis, the particle size of the chromatographic column packing is small and it is easy to be blocked by impurity particles. Therefore, samples and solvents need to be filtered in advance to remove particulate contaminants and protect the instrument. Ion chromatography, which is commonly used in environmental analysis, also requires that no inorganic pollutants be introduced in sample pretreatment. Syringe filters can be used in HPLC analysis and IC analysis to filter sample solutions, which is an important step in the sample pretreatment process.

High purity virgin polypropylene housing, no dyes or pigments added
Every unit type is available as an individually wrapped gamma sterilized pack
A unique concentric funnel-shaped barrel increases volume and decreases back pressure
Color-coded for easy identification
Place of Origin: China (Mainland)
Sample: Free
Payment: 100% T/T in advance

Aijiren is the leading supplier of chromatography consumables, can offer hplc vials,hplc syringe filter, EPA VOA vials, and some other test tubes.
Any requirement for chromatography consumables, please contact us.

When filtering samples choose right membrane syringe filter is very important. If you choose wrong syringe filters your chromatogrpahy instrument will be failed, which can waste a lot of time and money since liquids are normally very expensive. Aijiren provides cost-effective non-sterile and individual packed sterile syringe filters from Nylon, PES, PP, PTFE, PVDF, RC, etc. welcome to inquiry E-mail:info@aijirenvial.com whatsapp:+8618336073276

In HPLC analysis, the particle size of the chromatographic column packing is small and it is easy to be blocked by impurity particles. Therefore, samples and solvents need to be filtered in advance to remove particulate contaminants and protect the instrument.

Packing: Individually packaged, 100pcs per pack, 40PK/carton.56*50*26cm.12.5KG.packed in PP-Trays with plastic film and cover plate,neutral cartons outside OEM packing can be also provided.

Packing: Individually packaged, 100pcs per pack, 40PK/carton.56*50*26cm.12.5KG.packed in PP-Trays with plastic film and cover plate,neutral cartons outside OEM packing can be also provided.

Usage: Laboratory Analysis
Logo: Customized Accepted
Trademark: Aijiren
Origin: China
OEM: Available
Sample: Provided Freely

Available in sterile and non-sterile options

0.45um Syringe filters are normally used in scientific research laboratories to remove certain sized particles or bacteria from certain volume of liquid or gas prior to analysis or cell culture. 0.45um Syringe filters are popularly used in HPLC analysis.

The sample volume is 10-100 mL
Sprue: Luer-Lok™
Discharge port: Luer Slip
Made of polypropylene with a colored ring for identification
Pore ​​diameter and film type printed on the unit
High quality and cost-effective syringe filters are
available in a broad range of membrane materials
with sterile and non-sterile packaging options.

Aijiren offers an extensive selection of proven, yet affordable syringe filters that are in stock and ready to ship today. Selected for their durability, material quality, and performance characteristics, our syringe filters deliver accurate, measurable results at a fraction of the cost.
Diameter: 13mm and 25mm
Pore size: 0.22um and 0.45um
Package-Type: Low dust polyethylene box
Filter Housing: Polypropylene / High-Density Polyethylene
Industry-Specific Certification: Pharmaceutical Grade

Different Membrane syringe filter are available in Aijiren shop, The diameter of syringe filter are 13mm, 25mm, and 30mm. If you need other parameters syringe filter, you can ask our business manager. As we all know, the syringe filter is mainly used for prepare sample in chromatography system.

The syringe filters produced by Aijiren are of high quality, packaged and sold at reasonable prices. They are suitable for most major membrane materials, including nylon, PTFE, PES, MCE, PVDF, CA, PP and GF. They are available in 13mm, 17mm, 25mm and 30mm formats, and use a pure polypropylene shell.